·10 min read

Textile and automotive suppliers in Türkiye: CBAM, CSRD and data requests

Textiles are outside CBAM and so are most car parts, but steel fasteners, forged parts and aluminium castings are covered today. What EU buyers can ask Turkish suppliers under CBAM and CSRD, the value chain cap and the 2028 proposal.

Textile and automotive suppliers in Türkiye: CBAM, CSRD and data requests

Textiles are outside CBAM, and so are most automotive parts today. But steel screws, bolts, nuts and washers (CN 7318), forged, stamped and sintered steel articles (7326) and aluminium fasteners and castings (7616) have been CBAM goods since 2026, so an EU buyer importing them from a Turkish supplier needs verified embedded emissions data. For everything outside CBAM, the carbon data requests reaching suppliers mostly come from the buyer's own CSRD reporting: to report Scope 3, the buyer needs the supplier's energy use and Scope 1 and 2 emissions. On top of that, the Commission has proposed bringing gearboxes, road wheels, suspension systems and car bodies into CBAM from 2028; the proposal is not yet law.

This guide is written for EU procurement, sustainability and customs teams sourcing textiles or automotive components from Türkiye, and for the suppliers answering them. It separates which request rests on which rule and shows what a supplier can realistically provide. Sources: Annex I of CBAM Regulation 2023/956 (consolidated after 2025/2083), the Commission proposal COM(2025) 989 of 17 December 2025, Directive (EU) 2026/470 amending the CSRD, and Commission Recommendation (EU) 2025/1710 on the voluntary SME standard (VSME).

Which products fall under which rule?

The table maps typical products from both sectors to today's CBAM scope, the 2028 proposal and the data a buyer will most likely ask for. Final tariff classification is a customs question; check it with your broker.

ProductCBAM today2028 proposalData the buyer needs
Yarn, fabric, apparel, home textiles (chapters 50-63)Out of scopeNot on the proposed listCorporate footprint (energy, Scope 1 and 2), sometimes a per-product estimate
Steel screws, bolts, nuts, washers, rivets (7318)In scopeAlready coveredEmbedded emissions per good, verified operator's emissions report
Forged, stamped and sintered steel articles (7326)In scopeAlready coveredEmbedded emissions per good, verified operator's emissions report
Aluminium fasteners and castings (7616)In scopeAlready coveredEmbedded emissions per good, verified operator's emissions report
Gearboxes and parts (8708 40), road wheels (8708 70), suspension and shock absorbers (8708 80), car bodies (8707 10)Out of scopeProposedCorporate data today; steel and aluminium content for 2028

Automotive components already covered by CBAM

Annex I lists most of chapter 72 and selected headings of chapter 73. Two of them matter to the automotive supply chain: 7318 (screws, bolts, nuts, washers, rivets, cotter pins) and 7326 (other articles of iron or steel, including forged, stamped and sintered parts). For aluminium, 7616 (fasteners, castings and other articles of aluminium) is listed. Being made for a vehicle does not move a part into chapter 87: under the Harmonized System, parts of general use are excluded from the vehicle-parts heading, so bolts and nuts normally stay in 7318. "We only buy car parts, CBAM doesn't apply" is worth checking line by line in your import data.

The authorised CBAM declarant in the EU carries the declaration and certificate obligation once its annual imports of CBAM goods exceed 50 tonnes in total (hydrogen and electricity excluded). Vehicle manufacturers and parts distributors pass that threshold easily. Without actual data from the supplier, the declarant uses the Commission's default values plus a mark-up of 10% in 2026, 20% in 2027 and 30% from 2028.

Selected default values for Türkiye from the Commission's default value table (update of 6 August 2026, correcting act 2026/1740), before the mark-up:

CN codeProductDefault value, Türkiye (t CO2e / t of good)
7318 15Threaded screws and bolts5.430
7318 16Nuts3.790
7318 22 00Washers (excluding spring washers)3.430
7326 90 94Closed-die forged articles of iron or steel3.000
7616 10 00Aluminium screws, bolts, nuts, rivets and similar3.060

Example: you import 100 tonnes of 7318 15 bolts from a Turkish supplier in 2026 and receive no actual data. Embedded emissions are 100 × 5.430 = 543 tonnes; with the 10% mark-up, 597.3 tonnes. With actual data the figure has two parts: the supplier's direct installation emissions (for example natural gas in heat-treatment furnaces) and the embedded emissions of purchased precursors such as wire rod or wire. For iron and steel only direct emissions count. The supplier in turn needs precursor data from its steel mill; the method is explained in our steel embedded emissions guide, and the document list in what EU importers need from suppliers.

The 2028 proposal: vehicle parts may follow

On 17 December 2025 the Commission proposed extending CBAM to steel- and aluminium-intensive downstream goods (COM(2025) 989). Its financial statement refers to about 180 additional CN codes. Automotive-relevant entries include gearboxes and parts (8708 40), road wheels (8708 70), suspension systems and shock absorbers (8708 80), certain radiators (ex 8708 91), bodies for passenger cars (8707 10), chassis fitted with engines (8706), certain diesel engines (8408) and oil or petrol filters for combustion engines (ex 8421 23). The proposal would also treat pre-consumer steel and aluminium scrap as a precursor. Under the proposed text the extension applies from 1 January 2028.

Status: the Council agreed its negotiating position on 12 June 2026; the European Parliament adopted its amendments on 15 September 2026 and referred the file back for interinstitutional negotiations. The proposal is not law; the product list and the date can still change. Practical steps for buyers of these parts now:

  • Map the CN codes of the parts you import and ask suppliers for the steel and aluminium mass per part from their bill of materials.
  • Ask whether suppliers already obtain embedded emissions data from their steel and aluminium sources, and in what form.
  • Encourage suppliers to split fuel and electricity use by process or line; reconstructing that later is the hardest part.

Textiles: outside CBAM, so why the questionnaires?

Textile chapters are neither in today's CBAM list nor in the 2028 proposal, and the pilot phase of the Turkish ETS is limited to electricity, cement, iron and steel, aluminium and fertilisers. The data requests Turkish mills receive come from the buyer's side.

After Directive 2026/470, mandatory CSRD reporting applies to companies with net turnover above EUR 450 million and more than 1,000 employees on average. Their climate disclosures include significant Scope 3 categories, notably purchased goods and services, and that line is built from suppliers' Scope 1 and 2 emissions. Without supplier data, buyers fall back on spend-based averages, which cannot show a supplier's efficiency gains or fuel switching.

In textile wet processing, emissions typically come from two places: fuel for steam boilers in dyeing and finishing (Scope 1) and electricity for spinning, weaving and knitting machines (Scope 2). One trap for buyers comparing data: Turkish natural gas invoices state kWh on a gross (higher heating value) basis, while most emission factors are given per net calorific value, so multiplying invoice kWh directly overstates emissions by about 11%. Details in our data collection guide.

The value chain cap: what you may ask smaller suppliers

Directive 2026/470 introduced a cap to protect suppliers from disproportionate requests. A company in the value chain of a reporting undertaking that did not exceed an average of 1,000 employees in the preceding financial year is a "protected undertaking". The text does not distinguish between EU and non-EU suppliers. In practice this means:

  • A protected supplier may decline to provide information beyond the Commission's voluntary standard when the request is made for CSRD reporting.
  • The buyer must tell the supplier which requested items exceed the voluntary standard and that it has a statutory right to decline.
  • Contract clauses requiring more than the voluntary standard for CSRD purposes are not binding; the rest of the contract stands.
  • The buyer may rely on the supplier's self-declaration of size.

The cap does not prohibit voluntary sharing, does not cover requests for other purposes (EU due diligence rules, the buyer's risk management) and applies only to information gathering for CSRD reporting. CBAM data rests on a separate regulation and, in our reading, falls outside the cap. Member States must transpose these provisions by 19 March 2027.

The voluntary standard is to be based on the VSME in Recommendation 2025/1710. Its basic module disclosure B3 covers total energy consumption in MWh, split into electricity and fuels and into renewable and non-renewable; Scope 1 emissions under the GHG Protocol; location-based Scope 2 emissions; and GHG intensity, total emissions divided by turnover. Scope 3 is left as "can be appropriate" depending on activities. A supplier that has this set ready can answer most CSRD-driven questionnaires. See our Scope 1, 2 and 3 explainer for the definitions.

Three requests, one dataset

RequestLegal basisContentVerification
CBAM data requestCBAM Regulation, methodology regulation 2025/2547Embedded emissions per installation and good, precursors, sector parametersEU-accredited verifier required
CSRD supplier questionnaireBuyer's CSRD reporting (as amended by 2026/470)Energy, Scope 1 and 2, GHG intensity; value chain cap appliesNo legal requirement; buyer may ask
Product carbon footprintCommercial request, GHG Protocol Scope 3 methodsEmissions per part or per kilogram, allocation methodDepends on the buyer

All three draw on the same raw data: fuel and electricity records, production volumes and purchased materials. What differs is where the boundary is drawn and what the emissions are divided by.

A request checklist for buyers sourcing from Türkiye

  1. Classify first: list the CN codes you import; anything in 7318, 7326 or 7616 needs CBAM data now.
  2. Ask for a corporate inventory: Scope 1 and 2 under ISO 14064-1 or the GHG Protocol is the base for CSRD questionnaires. Our ISO 14064 GHG inventory page summarises the structure.
  3. Say why you ask: state whether a request is for CBAM, CSRD or a product footprint, and flag items beyond the voluntary standard.
  4. Ask for the allocation method: per kilogram, machine hour or piece, applied the same way for every customer.
  5. Accept one figure per installation and period: different numbers for different customers are a red flag.
  6. Plan for 2028 without betting on it: collect steel and aluminium content now; wait for the final text before changing contracts.

Common mistakes

  • Assuming automotive means no CBAM: fasteners and forged parts are covered today.
  • Accepting a corporate footprint as CBAM data: CBAM needs per-good, per-installation figures calculated with the EU method and verified.
  • Treating the 2028 list as final: it is still under negotiation.
  • Asking small suppliers for everything: beyond the voluntary standard, protected suppliers can say no.
  • Comparing gas data without checking the heating value basis: invoice kWh is gross.

Where Carbonet fits

Carbonet is a carbon management platform developed by LNA Soft in Izmir, Türkiye. It calculates corporate footprints in the six ISO 14064-1 categories and in Scope 1, 2 and 3 under the GHG Protocol, with department-level access so energy, purchasing or logistics teams enter and see only their own data. For CBAM goods such as fasteners or forged parts, the CBAM module lets a producer define CN codes, production processes and purchased precursors and calculate embedded emissions per good with the EU method. Data entered for the corporate footprint is not entered again for CBAM, so a supplier can answer a CSRD questionnaire and a CBAM request from one consistent dataset, in English or Turkish.

If you source from Turkish suppliers or answer carbon data requests yourself, we can walk you through it with real data. Request a demo or write to info@carbonet.com.tr (WhatsApp +90 533 368 05 99).

Frequently asked questions

Are textiles covered by CBAM?

No. Textile chapters 50-63 are not in Annex I of the CBAM Regulation and are not on the downstream list proposed for 2028. Carbon data requests to textile suppliers usually come from the buyer's CSRD reporting.

Are bolts and nuts made for vehicles CBAM goods?

Steel screws, bolts, nuts, washers and rivets are normally classified under CN 7318, which has been a CBAM heading since 2026. Being intended for vehicles does not change that. Confirm the classification with your customs broker.

Will gearboxes, wheels and shock absorbers be covered from 2028?

The Commission proposal COM(2025) 989 would add them from 1 January 2028. The Council set its position on 12 June 2026 and Parliament on 15 September 2026; the proposal is not yet law and the list and date may change.

How much can an EU buyer ask a small supplier under CSRD?

Suppliers with an average of up to 1,000 employees may decline CSRD-driven requests beyond the Commission's voluntary standard, and the buyer must flag which items exceed it. Member States must transpose the rule by 19 March 2027.

What minimum carbon data should a supplier have ready?

The energy and GHG disclosure in the VSME basic module: total energy use split into electricity and fuels, Scope 1 emissions, location-based Scope 2 emissions and GHG intensity per turnover.

Is a supplier's corporate footprint enough for CBAM?

No. CBAM requires embedded emissions per installation and good, calculated with the EU method, including precursors, and verified by an EU-accredited verifier. The same fuel, electricity and production data feeds both calculations.